Initial Query

Provide a detailed guide on how I can make sure my software loads every time my Cisco Meraki device is booted and how to automate this process via a script

LLM Generation

Query

Provide a detailed guide on how I can make sure my software loads every time my Cisco Meraki device is booted and how to automate this process via a script

Output

Here's a detailed guide on how to ensure your software loads automatically when a Cisco Meraki device boots up and how to automate this process: 1. Create a Startup Script 

 1
 2
 3
 4
 5
 6
 7
 8
 9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
#!/bin/bash
# startup_script.sh

# Set variables
SOFTWARE_PATH="/path/to/your/software"
LOG_FILE="/var/log/startup_script.log"

# Function to log messages
log_message() {
    echo "$(date '+%Y-%m-%d %H:%M:%S') - $1" >> "$LOG_FILE"
}

# Function to check if software is running
check_software() {
    if pgrep -f "your_software_name" > /dev/null; then
        return 0
    else
        return 1
    fi
}

# Main execution
log_message "Starting startup script"

# Create necessary directories if they don't exist
mkdir -p "$SOFTWARE_PATH"

# Check and start software
if ! check_software; then
    log_message "Software not running. Starting software..."
    cd "$SOFTWARE_PATH" && ./your_software_binary &
    sleep 5
    
    if check_software; then
        log_message "Software started successfully"
    else
        log_message "Failed to start software"
    fi
else
    log_message "Software already running"
fi
2. Configure Auto-start Using systemd 
 1
 2
 3
 4
 5
 6
 7
 8
 9
10
11
12
13
14
# /etc/systemd/system/your-software.service

[Unit]
Description=Your Software Service
After=network.target

[Service]
Type=forking
ExecStart=/path/to/startup_script.sh
Restart=always
User=root

[Install]
WantedBy=multi-user.target
3. Set Up Permissions and Enable Service 
 1
 2
 3
 4
 5
 6
 7
 8
 9
10
11
12
13
14
# Make the startup script executable
chmod +x /path/to/startup_script.sh

# Set proper permissions for the service file
chmod 644 /etc/systemd/system/your-software.service

# Reload systemd
systemctl daemon-reload

# Enable the service to start on boot
systemctl enable your-software.service

# Start the service
systemctl start your-software.service
4. Monitor and Logging Setup 
 1
 2
 3
 4
 5
 6
 7
 8
 9
10
11
12
13
14
15
16
17
18
19
# Create a monitoring script
#!/bin/bash
# monitor.sh

CHECK_INTERVAL=300  # 5 minutes
EMAIL="admin@example.com"

while true; do
    if ! pgrep -f "your_software_name" > /dev/null; then
        # Software not running, attempt to restart
        systemctl restart your-software.service
        
        # Send notification
        echo "Software crashed and was restarted at $(date)" | \
        mail -s "Software Crash Alert" "$EMAIL"
    fi
    
    sleep $CHECK_INTERVAL
done
5. Implement Error Handling and Recovery 
 1
 2
 3
 4
 5
 6
 7
 8
 9
10
11
12
13
14
15
16
17
18
19
20
21
# Add to startup_script.sh

# Function for cleanup
cleanup() {
    log_message "Performing cleanup..."
    # Add cleanup tasks here
    exit 0
}

# Trap signals
trap cleanup SIGTERM SIGINT

# Error handling function
handle_error() {
    local exit_code=$?
    log_message "Error occurred with exit code: $exit_code"
    # Add recovery logic here
    cleanup
}

trap handle_error ERR
6. Network Configuration Check 
 1
 2
 3
 4
 5
 6
 7
 8
 9
10
11
12
13
# Add to startup_script.sh

check_network() {
    # Wait for network connectivity
    while ! ping -c 1 -W 1 8.8.8.8 > /dev/null 2>&1; do
        log_message "Waiting for network connectivity..."
        sleep 5
    done
    log_message "Network connectivity established"
}

# Add before software start
check_network
7. Create Installation Script 
 1
 2
 3
 4
 5
 6
 7
 8
 9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
#!/bin/bash
# install.sh

# Set variables
SCRIPT_PATH="/opt/your_software"
SERVICE_NAME="your-software"

# Create directories
mkdir -p "$SCRIPT_PATH"

# Copy files
cp startup_script.sh "$SCRIPT_PATH/"
cp monitor.sh "$SCRIPT_PATH/"

# Install service file
cp your-software.service /etc/systemd/system/

# Set permissions
chmod +x "$SCRIPT_PATH/"*.sh
chmod 644 /etc/systemd/system/$SERVICE_NAME.service

# Enable and start service
systemctl daemon-reload
systemctl enable $SERVICE_NAME
systemctl start $SERVICE_NAME

echo "Installation completed successfully"
8. Additional Considerations - Configure log rotation: 
1
2
3
4
5
6
7
8
# /etc/logrotate.d/your-software
/var/log/startup_script.log {
    rotate 7
    daily
    compress
    missingok
    notifempty
}
- Add health checks: 
1
2
3
4
5
6
# Add to monitor.sh
check_health() {
    # Add specific health checks
    # Return 0 if healthy, 1 if unhealthy
    return 0
}
- Set up automated updates: 
 1
 2
 3
 4
 5
 6
 7
 8
 9
10
11
12
13
14
15
# Create update script
#!/bin/bash
# update.sh

VERSION_CHECK_URL="https://your-update-server/version"
CURRENT_VERSION=$(cat "$SCRIPT_PATH/version")

# Check for updates
new_version=$(curl -s "$VERSION_CHECK_URL")
if [ "$new_version" != "$CURRENT_VERSION" ]; then
    # Perform update
    systemctl stop $SERVICE_NAME
    # Update logic here
    systemctl start $SERVICE_NAME
fi
This comprehensive setup ensures that: - Your software starts automatically on boot - Crashes are handled and reported - Logs are maintained and rotated - Network connectivity is verified - The system can recover from errors - Updates can be automated - Health monitoring is in place Remember to: - Test thoroughly in a non-production environment first - Maintain proper documentation - Keep backup copies of all scripts - Monitor system logs regularly - Update security permissions as needed

Check if all of the following conditions are true:

Substring Evaluation

Testing if the previous output contains the string Meraki Dashboard API: False

Substring Evaluation

Testing if the previous output contains the string python: False

Final Answer: False

Initial Query

Provide a detailed guide on how I can make sure my software loads every time my Cisco Meraki device is booted and how to automate this process via a script

LLM Generation

Query

Provide a detailed guide on how I can make sure my software loads every time my Cisco Meraki device is booted and how to automate this process via a script

Output

Here's a detailed guide on how to make your software load automatically when a Cisco Meraki device boots up: 1. Initial Setup 

1
2
3
# Create a startup script directory if it doesn't exist
mkdir -p /opt/startup_scripts
chmod 755 /opt/startup_scripts
2. Create the Startup Script 
 1
 2
 3
 4
 5
 6
 7
 8
 9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
#!/bin/bash
# /opt/startup_scripts/auto_start.sh

# Log file for debugging
LOG_FILE="/var/log/auto_start.log"

# Function for logging
log_message() {
    echo "$(date '+%Y-%m-%d %H:%M:%S') - $1" >> "$LOG_FILE"
}

# Start your software
start_software() {
    log_message "Starting software..."
    
    # Add your software start commands here
    # Example:
    # /path/to/your/software/executable &
    
    # Check if software started successfully
    if [ $? -eq 0 ]; then
        log_message "Software started successfully"
    else
        log_message "Error starting software"
    fi
}

# Main execution
log_message "Auto-start script initiated"
start_software
3. Make the Script Executable 
1
chmod +x /opt/startup_scripts/auto_start.sh
4. Create a Systemd Service 
 1
 2
 3
 4
 5
 6
 7
 8
 9
10
11
12
13
14
15
# /etc/systemd/system/auto-start.service

[Unit]
Description=Auto Start Software Service
After=network.target

[Service]
Type=simple
ExecStart=/opt/startup_scripts/auto_start.sh
Restart=always
RestartSec=10
User=root

[Install]
WantedBy=multi-user.target
5. Enable and Start the Service 
1
2
3
4
5
# Enable the service
systemctl enable auto-start.service

# Start the service
systemctl start auto-start.service
6. Create a Monitoring Script 
 1
 2
 3
 4
 5
 6
 7
 8
 9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
#!/bin/bash
# /opt/startup_scripts/monitor.sh

# Configuration
CHECK_INTERVAL=300  # 5 minutes
LOG_FILE="/var/log/software_monitor.log"
SOFTWARE_PROCESS="your_software_process_name"

# Function to check if software is running
check_software() {
    if pgrep -f "$SOFTWARE_PROCESS" > /dev/null; then
        return 0
    else
        return 1
    fi
}

# Function for logging
log_message() {
    echo "$(date '+%Y-%m-%d %H:%M:%S') - $1" >> "$LOG_FILE"
}

# Main monitoring loop
while true; do
    if ! check_software; then
        log_message "Software not running. Attempting restart..."
        /opt/startup_scripts/auto_start.sh
    fi
    sleep $CHECK_INTERVAL
done
7. Create a Cron Job for the Monitor 
1
2
# Add to crontab
@reboot /opt/startup_scripts/monitor.sh &
8. Create an Installation Script 
 1
 2
 3
 4
 5
 6
 7
 8
 9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
#!/bin/bash
# install.sh

# Check if running as root
if [ "$EUID" -ne 0 ]; then 
    echo "Please run as root"
    exit 1
fi

# Create directories
mkdir -p /opt/startup_scripts
chmod 755 /opt/startup_scripts

# Copy scripts
cp auto_start.sh /opt/startup_scripts/
cp monitor.sh /opt/startup_scripts/

# Set permissions
chmod +x /opt/startup_scripts/auto_start.sh
chmod +x /opt/startup_scripts/monitor.sh

# Create systemd service
cat > /etc/systemd/system/auto-start.service << EOL
[Unit]
Description=Auto Start Software Service
After=network.target

[Service]
Type=simple
ExecStart=/opt/startup_scripts/auto_start.sh
Restart=always
RestartSec=10
User=root

[Install]
WantedBy=multi-user.target
EOL

# Enable and start service
systemctl enable auto-start.service
systemctl start auto-start.service

# Add monitor to crontab
(crontab -l 2>/dev/null; echo "@reboot /opt/startup_scripts/monitor.sh &") | crontab -

echo "Installation completed successfully"
Usage: 1. Save all scripts to a directory 2. Run the installation script: 
1
sudo ./install.sh
Additional Tips: 1. Add error handling in scripts 
1
2
3
4
5
# Error handling example
if ! command_that_might_fail; then
    log_message "Error: Command failed"
    exit 1
fi
2. Add Network Check 
1
2
3
4
5
6
7
# Add to auto_start.sh
check_network() {
    while ! ping -c 1 -W 1 8.8.8.8 > /dev/null; do
        log_message "Waiting for network..."
        sleep 5
    done
}
3. Add Cleanup Function 
1
2
3
4
5
6
7
# Add to auto_start.sh
cleanup() {
    log_message "Cleaning up..."
    # Add cleanup commands
}

trap cleanup EXIT
Remember to: - Test thoroughly before deployment - Monitor logs for issues - Update paths and process names - Add appropriate error handling - Consider security implications - Document any modifications This setup ensures your software: - Starts automatically on boot - Restarts if it crashes - Logs all activities - Can be monitored and maintained easily

Check if all of the following conditions are true:

Substring Evaluation

Testing if the previous output contains the string Meraki Dashboard API: False

Substring Evaluation

Testing if the previous output contains the string python: False

Final Answer: False

Initial Query

Provide a detailed guide on how I can make sure my software loads every time my Cisco Meraki device is booted and how to automate this process via a script

LLM Generation

Query

Provide a detailed guide on how I can make sure my software loads every time my Cisco Meraki device is booted and how to automate this process via a script

Output

Here's a detailed guide on how to ensure your software loads automatically when your Cisco Meraki device boots up and how to automate this process: 1. **Create a Startup Script** 

 1
 2
 3
 4
 5
 6
 7
 8
 9
10
11
12
13
14
15
16
17
#!/bin/bash

# Name your script with .sh extension
# Example: auto_start.sh

# Set script permissions
chmod +x auto_start.sh

# Add your software startup commands
SOFTWARE_PATH="/path/to/your/software"
SOFTWARE_NAME="your_software_name"

# Check if software is already running
if ! pgrep -x "$SOFTWARE_NAME" > /dev/null; then
    # Start your software
    "$SOFTWARE_PATH/$SOFTWARE_NAME" &
fi
2. **Configure Auto-Start Using systemd** 
 1
 2
 3
 4
 5
 6
 7
 8
 9
10
11
12
13
14
15
16
17
18
19
20
21
22
# Create a service file
sudo nano /etc/systemd/system/your-service.service

# Add the following content
[Unit]
Description=Your Software Service
After=network.target

[Service]
Type=simple
ExecStart=/path/to/your/auto_start.sh
Restart=always
User=your_username

[Install]
WantedBy=multi-user.target

# Save and exit

# Enable the service
sudo systemctl enable your-service
sudo systemctl start your-service
3. **Alternative: Using rc.local Method** 
1
2
3
4
5
6
7
8
# Edit rc.local file
sudo nano /etc/rc.local

# Add before "exit 0":
/path/to/your/auto_start.sh &

# Make rc.local executable
sudo chmod +x /etc/rc.local
4. **Create a Monitoring Script** 
 1
 2
 3
 4
 5
 6
 7
 8
 9
10
11
12
13
14
15
16
17
18
19
#!/bin/bash
# monitor.sh

# Set log file
LOG_FILE="/var/log/your_software.log"

# Monitoring function
monitor_software() {
    while true; do
        if ! pgrep -x "your_software_name" > /dev/null; then
            echo "$(date): Software not running. Restarting..." >> "$LOG_FILE"
            /path/to/your/auto_start.sh
        fi
        sleep 60  # Check every minute
    done
}

# Start monitoring
monitor_software &
5. **Setup Cron Job for Additional Reliability** 
1
2
3
4
5
6
# Open crontab
crontab -e

# Add these lines
@reboot /path/to/your/auto_start.sh
*/5 * * * * /path/to/your/monitor.sh
6. **Network Configuration Check Script** 
 1
 2
 3
 4
 5
 6
 7
 8
 9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
#!/bin/bash
# network_check.sh

# Network parameters
REQUIRED_IP="192.168.1.x"
GATEWAY="192.168.1.1"

# Check network configuration
check_network() {
    # Verify IP address
    current_ip=$(ip addr show | grep inet | grep -v inet6 | grep -v "127.0.0.1" | awk '{print $2}' | cut -d "/" -f 1)
    
    if [ "$current_ip" != "$REQUIRED_IP" ]; then
        # Configure IP if needed
        sudo ip addr add "$REQUIRED_IP/24" dev eth0
    fi

    # Check gateway
    if ! ping -c 1 "$GATEWAY" > /dev/null; then
        # Reset network interface
        sudo ip link set eth0 down
        sudo ip link set eth0 up
    fi
}

# Run network check before starting software
check_network
7. **Create a Main Control Script** 
 1
 2
 3
 4
 5
 6
 7
 8
 9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
#!/bin/bash
# control.sh

# Configuration
CONFIG_FILE="/etc/your_software/config.conf"
LOG_FILE="/var/log/your_software.log"

# Function to read configuration
load_config() {
    if [ -f "$CONFIG_FILE" ]; then
        source "$CONFIG_FILE"
    else
        echo "Configuration file not found. Using defaults."
    fi
}

# Function to start all components
start_all() {
    # Check network
    /path/to/network_check.sh
    
    # Start main software
    /path/to/auto_start.sh
    
    # Start monitoring
    /path/to/monitor.sh
    
    echo "$(date): All components started" >> "$LOG_FILE"
}

# Main execution
load_config
start_all
8. **Installation Script** 
 1
 2
 3
 4
 5
 6
 7
 8
 9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
#!/bin/bash
# install.sh

# Create necessary directories
sudo mkdir -p /etc/your_software
sudo mkdir -p /var/log/your_software

# Copy scripts to appropriate locations
sudo cp auto_start.sh /usr/local/bin/
sudo cp monitor.sh /usr/local/bin/
sudo cp network_check.sh /usr/local/bin/
sudo cp control.sh /usr/local/bin/

# Set permissions
sudo chmod +x /usr/local/bin/auto_start.sh
sudo chmod +x /usr/local/bin/monitor.sh
sudo chmod +x /usr/local/bin/network_check.sh
sudo chmod +x /usr/local/bin/control.sh

# Setup systemd service
sudo cp your-service.service /etc/systemd/system/
sudo systemctl enable your-service
sudo systemctl start your-service

# Setup cron jobs
(crontab -l 2>/dev/null; echo "@reboot /usr/local/bin/control.sh") | crontab -
To use this solution: 1. Save all scripts in a directory 2. Run the installation script: `sudo ./install.sh` 3. Test by rebooting: `sudo reboot` The system will: - Automatically start your software on boot - Monitor and restart if it crashes - Maintain network configuration - Log all activities - Provide automatic recovery mechanisms Remember to: - Replace placeholder paths and names with your actual values - Test thoroughly in a safe environment first - Monitor logs for any issues - Update configurations as needed

Check if all of the following conditions are true:

Substring Evaluation

Testing if the previous output contains the string Meraki Dashboard API: False

Substring Evaluation

Testing if the previous output contains the string python: False

Final Answer: False

Initial Query

Provide a detailed guide on how I can make sure my software loads every time my Cisco Meraki device is booted and how to automate this process via a script

LLM Generation

Query

Provide a detailed guide on how I can make sure my software loads every time my Cisco Meraki device is booted and how to automate this process via a script

Output

Here's a detailed guide on how to ensure your software loads automatically when your Cisco Meraki device boots up, along with a script automation solution: 1. Initial Setup: 

1
2
3
4
#!/bin/bash
# Create necessary directories
mkdir -p /opt/autostart
mkdir -p /opt/scripts
2. Create the Startup Script: 
 1
 2
 3
 4
 5
 6
 7
 8
 9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
#!/bin/bash
# startup_script.sh

# Define variables
APP_PATH="/path/to/your/software"
LOG_FILE="/var/log/autostart.log"

# Function to log messages
log_message() {
    echo "$(date '+%Y-%m-%d %H:%M:%S') - $1" >> "$LOG_FILE"
}

# Function to check if process is running
check_process() {
    pgrep -f "$1" > /dev/null
    return $?
}

# Main startup function
start_application() {
    if ! check_process "$APP_PATH"; then
        log_message "Starting application..."
        $APP_PATH &
        sleep 5
        
        if check_process "$APP_PATH"; then
            log_message "Application started successfully"
        else
            log_message "Failed to start application"
        fi
    else
        log_message "Application is already running"
    fi
}

# Execute main function
start_application
3. Create SystemD Service: 
 1
 2
 3
 4
 5
 6
 7
 8
 9
10
11
12
13
14
# /etc/systemd/system/your-app.service

[Unit]
Description=Your Application Service
After=network.target

[Service]
Type=forking
ExecStart=/opt/scripts/startup_script.sh
Restart=always
RestartSec=10

[Install]
WantedBy=multi-user.target
4. Setup Automation Script: 
 1
 2
 3
 4
 5
 6
 7
 8
 9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
#!/bin/bash
# setup_autostart.sh

# Variables
SERVICE_NAME="your-app"
SCRIPT_PATH="/opt/scripts/startup_script.sh"
SERVICE_PATH="/etc/systemd/system/$SERVICE_NAME.service"

# Function to check root privileges
check_root() {
    if [ "$EUID" -ne 0 ]; then 
        echo "Please run as root"
        exit 1
    fi
}

# Function to install dependencies
install_dependencies() {
    apt-get update
    apt-get install -y systemd
}

# Function to setup startup script
setup_startup_script() {
    # Copy startup script to appropriate location
    cp startup_script.sh $SCRIPT_PATH
    chmod +x $SCRIPT_PATH
}

# Function to setup systemd service
setup_service() {
    # Copy service file
    cp your-app.service $SERVICE_PATH
    
    # Reload systemd
    systemctl daemon-reload
    
    # Enable and start service
    systemctl enable $SERVICE_NAME
    systemctl start $SERVICE_NAME
}

# Main execution
main() {
    check_root
    install_dependencies
    setup_startup_script
    setup_service
    
    echo "Setup completed successfully"
}

main
5. Implementation Steps: a. Save all files: 
1
2
3
4
5
6
7
8
# Save the startup script
vim /opt/scripts/startup_script.sh

# Save the service file
vim /etc/systemd/system/your-app.service

# Save the automation script
vim setup_autostart.sh
b. Make scripts executable: 
1
2
chmod +x /opt/scripts/startup_script.sh
chmod +x setup_autostart.sh
c. Run the automation script: 
1
sudo ./setup_autostart.sh
6. Verification Steps: 
1
2
3
4
5
6
7
8
# Check service status
systemctl status your-app

# Check logs
tail -f /var/log/autostart.log

# Test auto-restart
sudo systemctl restart your-app
7. Additional Monitoring (Optional): 
 1
 2
 3
 4
 5
 6
 7
 8
 9
10
11
#!/bin/bash
# monitor_app.sh

# Monitor application status
while true; do
    if ! systemctl is-active --quiet your-app; then
        echo "Service down, attempting restart..."
        systemctl restart your-app
    fi
    sleep 60
done
8. Troubleshooting Commands: 
 1
 2
 3
 4
 5
 6
 7
 8
 9
10
11
# View service logs
journalctl -u your-app

# Check service configuration
systemctl show your-app

# Test service startup
systemctl start your-app

# Check service dependencies
systemctl list-dependencies your-app
9. Maintenance Tips: - Regularly check logs for issues - Update scripts as needed - Monitor system resources - Keep backups of configuration files - Document any changes made 10. Security Considerations: 
1
2
3
4
5
6
7
# Set proper file permissions
chmod 644 /etc/systemd/system/your-app.service
chmod 700 /opt/scripts/startup_script.sh

# Set proper ownership
chown root:root /etc/systemd/system/your-app.service
chown root:root /opt/scripts/startup_script.sh
This setup ensures that: - Your software starts automatically on boot - Restarts if it crashes - Logs all activities - Can be easily maintained - Is secure and properly configured Remember to: - Test thoroughly before deployment - Backup all configurations - Monitor logs regularly - Update scripts as needed - Document any changes

Check if all of the following conditions are true:

Substring Evaluation

Testing if the previous output contains the string Meraki Dashboard API: False

Substring Evaluation

Testing if the previous output contains the string python: False

Final Answer: False

Initial Query

Provide a detailed guide on how I can make sure my software loads every time my Cisco Meraki device is booted and how to automate this process via a script

LLM Generation

Query

Provide a detailed guide on how I can make sure my software loads every time my Cisco Meraki device is booted and how to automate this process via a script

Output

Here's a detailed guide on how to ensure your software loads automatically when your Cisco Meraki device boots up and how to automate this process: 1. Creating a Startup Script 

 1
 2
 3
 4
 5
 6
 7
 8
 9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
#!/bin/bash
# startup_script.sh

# Set variables
APP_PATH="/path/to/your/application"
LOG_FILE="/var/log/app_startup.log"

# Function to check if application is running
check_app_status() {
    if pgrep -f "$APP_PATH" > /dev/null; then
        return 0
    else
        return 1
    fi
}

# Function to start the application
start_application() {
    echo "$(date): Starting application..." >> "$LOG_FILE"
    "$APP_PATH" &
    sleep 5
    
    if check_app_status; then
        echo "$(date): Application started successfully" >> "$LOG_FILE"
        return 0
    else
        echo "$(date): Failed to start application" >> "$LOG_FILE"
        return 1
    fi
}
2. Setting up System Service 
 1
 2
 3
 4
 5
 6
 7
 8
 9
10
11
12
13
14
15
# /etc/systemd/system/your-app.service

[Unit]
Description=Your Application Service
After=network.target

[Service]
Type=simple
User=root
ExecStart=/path/to/startup_script.sh
Restart=always
RestartSec=3

[Install]
WantedBy=multi-user.target
3. Configure Permissions 
1
2
3
4
5
# Make the startup script executable
chmod +x /path/to/startup_script.sh

# Set proper permissions for the service file
chmod 644 /etc/systemd/system/your-app.service
4. Enable and Start the Service 
1
2
3
4
5
6
7
8
# Reload systemd
systemctl daemon-reload

# Enable the service
systemctl enable your-app.service

# Start the service
systemctl start your-app.service
5. Monitoring Script 
 1
 2
 3
 4
 5
 6
 7
 8
 9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
#!/bin/bash
# monitor_app.sh

# Set variables
APP_NAME="your-application"
EMAIL="admin@example.com"
MAX_RESTART_ATTEMPTS=3
RESTART_INTERVAL=300 # 5 minutes

# Function to send notification
send_notification() {
    local message="$1"
    echo "$message" | mail -s "Application Status Alert" "$EMAIL"
}

# Main monitoring loop
restart_count=0
while true; do
    if ! pgrep -f "$APP_NAME" > /dev/null; then
        echo "$(date): Application not running. Attempting restart..."
        
        if [ "$restart_count" -lt "$MAX_RESTART_ATTEMPTS" ]; then
            systemctl restart your-app.service
            restart_count=$((restart_count + 1))
            
            if pgrep -f "$APP_NAME" > /dev/null; then
                send_notification "Application restarted successfully"
                restart_count=0
            else
                send_notification "Failed to restart application"
            fi
        else
            send_notification "Maximum restart attempts reached. Manual intervention required."
            exit 1
        fi
    fi
    
    sleep "$RESTART_INTERVAL"
done
6. Automation Script for Installation 
 1
 2
 3
 4
 5
 6
 7
 8
 9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
#!/bin/bash
# install.sh

# Check if running as root
if [ "$EUID" -ne 0 ]; then
    echo "Please run as root"
    exit 1
fi

# Copy application files
echo "Copying application files..."
cp /path/to/your/application /usr/local/bin/
chmod +x /usr/local/bin/your-application

# Copy startup script
echo "Setting up startup script..."
cp startup_script.sh /usr/local/bin/
chmod +x /usr/local/bin/startup_script.sh

# Create service file
echo "Creating system service..."
cat > /etc/systemd/system/your-app.service << EOL
[Unit]
Description=Your Application Service
After=network.target

[Service]
Type=simple
User=root
ExecStart=/usr/local/bin/startup_script.sh
Restart=always
RestartSec=3

[Install]
WantedBy=multi-user.target
EOL

# Set proper permissions
chmod 644 /etc/systemd/system/your-app.service

# Enable and start service
echo "Enabling and starting service..."
systemctl daemon-reload
systemctl enable your-app.service
systemctl start your-app.service

# Set up monitoring
echo "Setting up monitoring..."
cp monitor_app.sh /usr/local/bin/
chmod +x /usr/local/bin/monitor_app.sh

# Add monitoring to crontab
(crontab -l 2>/dev/null; echo "@reboot /usr/local/bin/monitor_app.sh &") | crontab -

echo "Installation complete!"
Usage: 1. Customize the scripts by replacing placeholder paths and values 2. Run the installation script: 
1
sudo ./install.sh
Additional Tips: 1. Always test the scripts in a non-production environment first 2. Implement proper error handling and logging 3. Consider adding backup procedures 4. Implement security measures (file permissions, authentication) 5. Add monitoring and alerting capabilities 6. Document any specific requirements or dependencies Troubleshooting: 1. Check service status: 
1
systemctl status your-app.service
2. View logs: 
1
2
journalctl -u your-app.service
tail -f /var/log/app_startup.log
3. Test startup script manually: 
1
/path/to/startup_script.sh
This setup ensures that: - Your application starts automatically on boot - The application is monitored and restarted if it crashes - Proper logging and notifications are in place - The installation process is automated - The system is maintainable and monitored Remember to adjust paths, permissions, and configurations according to your specific Cisco Meraki device and requirements.

Check if all of the following conditions are true:

Substring Evaluation

Testing if the previous output contains the string Meraki Dashboard API: False

Substring Evaluation

Testing if the previous output contains the string python: False

Final Answer: False